Uvp B-100 Series Bedienungsanleitung PDF herunterladen

B-100 Series Ultraviolet Lamps

Operating Instructions

These Instructions cover UVP’s high-intensity 100-watt

B-100 series lamps (115V and 220V). The B-100AP,

B-100AP/R and B-100YP models are manufactured with

UVP’s Cool-Touch™ plastic housing. B-100A, B-100A/R

and B-100Y models are manufactured of a durable

scratch-resistant, powder-painted aluminum. The

B-100Y and B-100YP models feature a yellow filter.

Lamp and accessory drawings and replacement parts

lists for each model are included in these instructions.

This manual covers the following lamp part numbers:

Part Numbers

Model 115V 230V

B-100AP 95-0127-01 95-0127-02

B-100AP/R 95-0127-06 95-0127-07

B-100YP 95-0127-03 95-0127-04

B-100Y 95-0044-24 95-0044-18

B-100A 95-0044-22 95-0044-02

B-100A/R 95-0044-03 95-0044-03

General Information for Ultraviolet Inspection

Make tests in a darkened area for best contrast. Fluorescence may be bright or dim, depending on amount

of fluorescing agent present. Be careful to distinguish fluorescence from blue light reflection on polished

metal surfaces. UVP Model UVC-503 Safety Goggles are recommended to eliminate blue haze resulting

from eye fluorescence caused by reflected longwave ultraviolet radiation.

Installation

An 8-foot primary and secondary line cord is supplied on all units except the B-100AP/R and B-100A/R which

come with 8-foot primary and 20-foot secondary line cords. If the receptacle is not fitted with 3-prong plug,

use a 2-prong adapter and attach grounding lead to screw center of receptacle plate. Some units may ship

with bare wire leads. Connect the appropriate plug for your area.

Operation

Turn on/off switch on transformer base to ON position for starting. Although a cool lamp starts immediately,

allow approximately five minutes to reach full brilliance. When use is intermittent, it is preferable to leave the

lamp burning. This assures longer bulb life and avoids delay in restarting. Restarting does not take place

immediately as the mercury vapor within the bulb must cool. Delay is typically 4 to 8 minutes. Any interruption

in the power supply, such as an excessive drop in voltage, will extinguish the arc. Restarting typically will be

delayed while the mercury vapor cools. Full voltage must be restored to permit the arc to strike.

While mounted on the transformer base, the lamp housing can rotate 360°. For handheld use, detach the lamp

housing from the transformer base.

81-0093-01 Rev N

B-100AP

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Operating Instructions

B-100 Series Ultraviolet Lamps Operating Instructions These Instructions cover UVP’s high-intensity 100-watt B-100 series lamps (115V and 220V). The

Seite 2 - B-100AP, B-100AP/R, B-100YP

Replacement Parts List Parts lists are provided for the B-100 lamp models. Two parts lists are shown: one for the Cool-Touch housing lamps and one

Seite 3 - Accessories

CAUTION 1. Wear hand and eye protection if filter glass is cracked. Replace filter as soon as possible. 2. To avoid electrical shock hazard, unpl

Seite 4 - Product Warranty

The Finger Guard, to keep fingers away from the filter glass, easily snaps into place on the face of the Cool-Touch lamps. To install, remove the la

Kommentare zu diesen Handbüchern

Keine Kommentare

Uvp B-100 Series Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Beleuchtung Uvp B-100 Series herunter. UVP B-100 Series User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Beleuchtung Uvp B-100 Series